Press release
ASTM International Publishes Revised Fire Safety Standard for Candles
• Clearer definitions of religious/ceremonial candles based on size. In general, these candles are 17 inches or more and other candles for worship, that are used at home, are now regarded as “extended use candles”
• Candle Burning Performance Test has been altered to account for burning of extended use candles, which are now specified to burn for the prescribed length of time, instead of 8 hours for gel-containing candles and 4 hours for other types of candles
• Plastic container flammability tests are changed. The 2016 version required both total burn time not to exceed 300 seconds for 10 samples and individual burn time not to exceed 30 seconds. The 2017 version adds requirement which states “no single plastic container shall be completely consumed during testing”
The last change removes the gap in the 2016 version of the standard that did not cover extremely flammable plastic containers that totally burnt up in less than 30 seconds.
ASTM F2417 sets out the minimum safety requirements for candles with the intention of reducing fires, deaths, and injuries when burning a candle.
SGS Consumer Product Services
SGS is committed to providing information about development in regulations for consumer products as complimentary services. Through a global network of laboratories, SGS provides a wide range of services including physical/mechanical testing, analytical testing and consultancy work for technical and non-technical parameters applicable to a comprehensive range of consumer products. Learn more about SGS’s Consumer Product Services. [www.sgs.com/cgnr]
SGS SafeGuardS keep you up to date with the latest news and developments in the consumer goods industry. Read the full US Fire Safety Standard for Candles, ASTM F2417, Updated to 2017 Version SafeGuardS. [www.sgs.com/en/news/2017/11/safeguards-17317-fire-safety-standard-for-candles]
Subscribe here, www.sgs.com/subscribesg, to receive SGS SafeGuardS direct to your inbox.
For further information contact:
Leo Fung
Technical Services Executive
Tel: 852-27747168
Email: crs.media@sgs.com
Website: www.sgs.com/hardlines
About SGS
SGS is the world’s leading inspection, verification, testing and certification company. SGS is recognized as the global benchmark for quality and integrity. With more than 90,000 employees, SGS operates a network of over 2,000 offices and laboratories around the world.
1, Mons Calpe
Chitcombe Road
Broad Oak
Rye
East Sussex
TN31 6EU
This release was published on openPR.
Permanent link to this press release:
Copy
Please set a link in the press area of your homepage to this press release on openPR. openPR disclaims liability for any content contained in this release.
You can edit or delete your press release ASTM International Publishes Revised Fire Safety Standard for Candles here
News-ID: 849503 • Views: …
More Releases from SGS
SGS Summarizes Strengthened EU Specifications for HBCDD Under the POP Recast Reg …
SGS, the world's leading testing, inspection and certification company, has published details of revised hexabromocyclododecane (HBCDD) specifications under the European Union's (EU) persistent organic pollutants legislation, the POP Recast Regulation (EU) 2019/1021.
HBCDD is a flame retardant found in many consumer items, including upholstery and textiles, as well as in electric and electronic equipment.
The EU Commission's Delegated Regulation (EU) 2024/2555 of March 21, 2024, published on September 27, 2024, revises the…
SGS Summarizes Impact of EU Postponement of RED Cybersecurity Regulation Enforce …
SGS, the world's leading testing, inspection and certification company, has published SafeGuardS 095.23 to help stakeholders understand the impact of the decision to postpone the enforcement of the Radio Equipment Directive (RED) delegated act for cybersecurity until 2025.
The European Commission (EC) originally planned to enforce the delegated act from August 2024. However, delays in the preparation of harmonized standards have meant the EC has now taken the decision to enforce…
SGS Issues SafeGuardS for US CPSC Direct Final Rule for Bedside Sleepers
SGS, the world's leading testing, inspection and certification company, has published a SafeGuardS covering a recent direct final rule for bedside sleepers issued by the US Consumer Products Safety Commission (CPSC).
Direct final rule 16 CFR 1222 was published on May 9, 2023, revising the safety standard for bedside sleepers. It incorporates the latest version of ASTM F2906-23 (Standard Consumer Safety Specification for Bedside Sleepers) with a modification. The modification involves…
SGS Announces Complementary Webinar to Help Businesses Navigate Post-Brexit Euro …
SGS, the world's leading testing, inspection and certification company, has announced a webinar to help companies operating in European personal protective equipment (PPE) markets understand the implications of Brexit and the best route towards compliance.
"Personal Protective Equipment: overview of EU and UK requirements" will be offered in two sessions on February 9, 2023, at 10.00 CET and 16.00 CET. It is aimed at operators throughout the PPE value chain, including…
More Releases for ASTM
ASTM A333 Seamless Low Temperature Steel Pipe
Product introduction ASTM A333 is the standard specification given to all the welded as well as seamless steel, carbon and alloy pipes which are intended to be used at places of low temperatures. The ASTM A333 pipes are used as heat exchanger pipes and pressure vessel pipes.
As it was stated in the above section, that these pipes are used in the areas where temperature is extremely low, they are used…
Difference between ASTM A513 and ASTM A500 rectangular tubes
What is a rectangular tube?
Rectangular tube is a long hollow steel material with a rectangular cross-section. They are typically made of steel, aluminum, or other metals and have a variety of uses and applications. When the bending and torsion strength are the same, the weight is lighter, so it is widely used in manufacturing mechanical parts and engineering structures.
The difference between ASTM A513 and ASTM A500 rectangular tubes:
ASTM A500 (also…
Youfa Steel Pipe Group: ASTM A53 Carbon Steel Pipe Manufacturer
Short Description:
Youfa Advantange:
1.100% after-sales quality and quantity assurance. 22 years experience in manufacturing and exporting steel products since 2000.
2. Large Stock for regular sizes. 16 Consecutive Years of The First Production and Sales-Over 1300,0000 Tons sales and production
3. Strong produce capability and capital flow.
4. Listed company in Shanghai Exchange Stock
5. Top 500 manufacturing of China
6. National 3A grade industrial park tourist attractions - Green and environment-friendly factory Min. Order Quantity:…
ASTM F963-16 is Accepted as Mandatory Toy Safety Standard
On February 2, 2017, the US Consumer Product Safety Commission (CPSC) published a direct final rule in the Federal Register authorizing ASTM F963-16 as the consumer product safety standard for toys.
ASTM F963-16, issued in October 2016 by the American Society for Testing and Materials (ASTM), contains several important changes from previous versions of the standard. These include changes relating to:
• Magnets
• Projectiles
• Toy Chests
• Batteries
• Microbiological Safety
• Heavy Elements, such as heavy metals in textiles…
Voluntary Safety Standard for Liquid Laundry Packets Published by ASTM
ASTM International has published a standard for liquid laundry packets. The standard details labeling, warning statements, specifications and testing methods for determining: content retention, force compression, and the presence of aversive agents in the soluble film.
The key points of the new standard are:
• It applies exclusively to household liquid laundry detergent packets
• Packaging should be opaque or otherwise mask the visibility of the packets. Graphics that make the packaging appear translucent or…
ASTM Revises Standards for Children’s Chairs and Stools
The standards organization, ASTM International (ASTM), has revised its safety standard for Children’s Chairs and Stools. Published in May 2016, the new standard, ASTM F2613-16, replaces ASTM F2613-14.
The new standard has added a number of changes, including:
• Addition of a definition for chairs with side containment
• Revision of the definition for rigid frame
• Changing the requirement and test method for stability
• Addition of standards for sideways stability for chairs with side containment
• Addition of…
