Major U.S. Heat Treater Selects MHV Pumps for Vacuum Furnace Application
Survivor™ models increase service life and reliability
Metallurgical High Vacuum HD300 Survivor pumps down the furnace from atmosphere; its pressurized oil system includes filtration
Fennville, MI --- MHV shipped another Survivor™ model HD300 vacuum pump for a heat treating furnace built by Ipsen® going to a major heat treater in the USA.
According to Geoff Humberstone, MHV President," The customer chose the MHV pumps for their longer life capabilities with positive pressure oil filtration in severe environments.
The HD300 provides longer life because of it robust construction and filtration that minimizes acids and contaminants that can kill other pumps." We look for future orders from heat treaters which want longer life and less downtime."
MHV Survivor™ vacuum pumps use a proven oil-sealed rotary piston design for excellent reliability even in demanding operating conditions encountered in heat treating. Their pressurized oil lubrication increases pump life significantly by filters that clean the oil of particulates and acids. Clean oil is forced into the critical hinge bar/piston slide tang interface. The eccentric bearing bands are also pressure lubricated.
This pump design reduces the cost of ownership over the life of the pump, and helps to reduce periodic maintenance. A standard gear-type oil pump provides positive lubrication of bearings and all other moving parts. The heavy-duty roller bearing design on main shaft extends life and gives better resistance to corrosion.
The Ipsen* furnace is designed for heat treating parts at a major Commercial Heat Treating Plant operating on multiple shifts. The customer wanted longer pump life and specified an MHV Survivor™ pump.
The Ipsen HR54X48 chamber has a hot zone which is 36 inches wide x 48 inches deep x 36 inches tall. The HD-300 oil-sealed piston is the roughing pump working with a Stokes® 615 Vacuum Blower pump having a capacity of 2000 CFM (943 liters/sec). The Ipsen Furnace can operate at 2400° F and 10ˉ⁶ Torr with heat exchanger for quenching.
Humberstone further comments, “We have 15 Survivor pumps with over 300,000 hours in operation. Their “Smart Filters™” are soaking up the acids and particles that can kill standard pumps.”
Visit our website: www.methivac.com or call MHV at: 877-787-9880 to learn more.
*Ipsen USA, Headquarters, 984 Ipsen Rd., Cherry Valley, IL 61016 www.ipsenusa.com
About Metallurgical High Vacuum
Metallurgical High Vacuum Corporation is a vital supplier in the vacuum technology industry. With over a quarter-century in the business, they have earned a reputation for responsiveness with high quality engineering and manufacturing that is unsurpassed. Customers depend on MHV for keeping their operations running, and costs under control. MHV offers rebuilding services for vacuum pumps and blowers. Its products and services include new pumps and systems, vacuum piping and manifolds, flexible connectors, vacuum valves, custom oil filtration systems, helium leak testing, and field repair. Rental pumps and blowers are also available; call to check inventory.
Geoff Humberstone, Pres.
Metallurgical High Vacuum
6708 124th Avenue
Fennville, MI 49408
FAX: (269) 543-4750
Press Contact: Jim Martin
Metallurgical High Vacuum
This release was published on openPR.
Permanent link to this press release:
Please set a link in the press area of your homepage to this press release on openPR. openPR disclaims liability for any content contained in this release.
You can edit or delete your press release Major U.S. Heat Treater Selects MHV Pumps for Vacuum Furnace Application here
News-ID: 275548 • Views: 2909
More Releases from Metallurgical High Vacuum
Metallurgical High Vacuum Announces High Vacuum Newsletter
Fennville, MI---Metallurgical High Vacuum has created a new “High Vacuum News” to provide heat treat industry professionals with tips and hints to keep their vacuum pumps running strong. As Geoff Humberstone, MHV President, comments: “This year marks 30 years for us as Metallurgical High Vacuum. Back in 1981, I saw the need for vacuum design and consulting and started the company. Within four years we added pump remanufacturing because we
Metallurgical High Vacuum Exhibits at Furnaces North America
Fennville, MI--- Metallurgical High Vacuum will show its newest vacuum pump a 430-CFM HS 430 at Booth # 620-622 at the FNA show in Orlando, Florida*, on October 5—6, 2010. The booth will also feature information on rebuilt vacuum pumps for tough heat treating applications, at which MHV excels. Also on display will be mechanical seal retrofits for the Roots® 615 blower and Stokes® 306/310 blower. Below the cost of
Metallurgical High Vacuum Ships Vacuum Chambers
Special Designs are Built to Customer Specifications Fennville, MI--- Metallurgical High Vacuum recently shipped two chambers for customer-specific applications. One vacuum chamber is over 72” high and will be used in atomic layer deposition (ALD) to strengthen glass used in LCD's for phones. The other chamber is a 12-inch square design that will be used to weld silicon sticks, complete with a two-stage booster vacuum pumping system. Both chambers are
Metallurgical High Vacuum Debuts "Torture Tank" To Assure Peak Pump & Blower Per …
Fennville, MI--- Until now, most replacement vacuum pumps were tested under actual conditions only when they were first connected to a customer’s heat treating chamber. Now, Metallurgical High Vacuum puts their new and rebuilt pumps and blowers through their torturous “stress test” at the factory to assure performance under pump-down conditions. As Geoff Humberstone, MHV President, comments: “We have always done a blank off test and a 20-24 hour
More Releases for Survivor
Cancer survivor beats the odds to get shortlisted in Rural Business Awards
A Sussex woman who set up her business from scratch, while at the same time fighting breast cancer, is in the running for an award. She hopes to show others that with a good idea and determination to succeed anything is possible. Sue Harbottle-Sear, from East Hoathly, has been shortlisted in two categories of the Rural Business Awards after impressing the judges with her story about Konzepts and her ethos of
18 years later Survivor Eagle Scout flys full circle
Erie, PA Ryan K. Kolacek, who completed his Eagle Scout board of review at HealthSouth Erie in ‘99, will be a Merit Badge counselor for Penn State Behrend’s Boy Scouts Go To College Day on May 19th, 2018. Kolacek will be the Graphic Arts, and Digital Technology Merit Badge Counselor with almost 15 years experience as an Art Director. He will bring industry knowledge to highlight merit badge requirements for local Boy
Cancer survivor launches safe, all-natural cosmetic brand
Basildon, Essex– Babylon Tree, a brand new, full-service natural cosmetics business created to provide consumers with sustainable access to natural soaps, bath accessories, and cosmetic products, was officially opened in Basildon, Essex. Borne from a passion from a father-to-be who was diagnosed with cancer and underwent 25 session of radiotherapy treatments followed by a major operation, Babylon Tree represents the hope and pureness of using only nature’s most pristine and chemically-free
Two-Time Breast Cancer Survivor Launches Pink Ribbon Annex
Specializing in services and specialty garments for the beast cancer community, as well as a trusted resource for health and wellness news. San Diego, CA, April 04, 2012 -- Daunting as it may seem, 1 in 8 women will be diagnosed with breast cancer during their lifetime - there is no manual, no protocol, and no warning. While there are countless websites and organizations committed to building awareness and educating women
Sangram Singh’s Sportsmanship In Survivor India
Being blindfold and even thus having the ability to see the right move was not an easy job. To achieve the goal on time is appreciable but to reach towards goal even without having a view of it was up to the mark. The right use of the power with perfect blending of brain and coordination leads Catan Tribe to do something which remained an extra ordinary move of the
CRISIS SURVIVOR GOES INTO ADMINISTRATION OWING £300,000
11 May 2011 PRESS RELEASE CRISIS SURVIVOR GOES INTO ADMINISTRATION Owing over £300,000 Crisis Survivor, the risk management and business continuity specialist, has gone into receivership, leaving 38 creditors and debts of £312,599. The directors of Crisis Survivor who were responsible for implementing Crisis Survivor’s strategy and driving the business forward include Michael Walker, a former Prudential Financial executive; Tony Gimple, who previously worked for American Express and Chancery Law Group; Richard Vardy, former company