openPR Logo
Press release

With high speed in the concrete

08-27-2013 11:09 AM CET | Industry, Real Estate & Construction

Press release from: IBJ Technology

compressive stress sensor

compressive stress sensor

With the sensor BBS 10_DS from IBJ Technology, surface pressure in concrete components can be determined also afterwards. The applications range from the direct stress measurement in the component to the measurement and monitoring of dynamic loads in real time.

Ultrasonic captures the stress in the structure directly and in real time. All changes can be transferred online via the Internet or satellite radio. The sensors are either placed directly in the building, or subsequently attached to exposed to. Construction elements or bridges bearing may be easily monitored. The sensors are constantly active on or in the building. The simple design and small size allow the full application of all structures made of steel or concrete. All civil engineering works are static loads and measure voltages and small dynamic changes.
After the procedure, many important civil engineering works could be monitored worldwide. The costs of such controls are minimal.
The collapse of buildings goes hand in hand with a measurable change of stresses and loads. These are correlated with the stove data of seismic events worldwide available and checked for plausibility. This surveillance of buildings of all kinds on damage caused by disasters (soil landslides, earthquake, mudslide, etc.) also is possible.

A low overall height of the sensors was elected to allow installation in boreholes for many different applications. The installation of the sensors is diameter holes approximately 1 inch.
Each sensor is clearly identifiable with the encoding of sensor in Rome.

Approx. up to 50,000 measurements per second can be made with a suitable control and evaluation unit.
The monitoring of all possible curtails and structural parameters during the construction and operation of buildings is the basis for the State and safety analysis of the building. On-line measuring method with the sensors from IBJ Technology force and load measurement, especially stress measurements in concrete, are not to replace their validity and relevance.

IBJ Technology as a partner of the industry for the interests of process measurement technology was founded in January 2003.

Owner of the Engineering Office for innovative measuring technology is Mr. Dipl.-Ing. (TH), Dipl-Ing.-oec. Frank-Michael Jaeger.

IBJ Technology
Colkwitzer Weg 7
04416 Markkleeberg

+49(0)341 330172

This release was published on openPR.

Permanent link to this press release:

Please set a link in the press area of your homepage to this press release on openPR. openPR disclaims liability for any content contained in this release.

You can edit or delete your press release With high speed in the concrete here

News-ID: 266827 • Views: 4738

More Releases from IBJ Technology

.Smart Rock Stress Sensor with MEMS
The RSS-X series of acousto elastic sensors from IBJ Techhnology is used to measure variations in compressive stress and load, which allows stress evaluation when the material’s modulus of elasticity is unknown or anisotropic and inhomogeneous. Typical examples are concretes and drill holes in the rocks, where these instruments can be used include: • Mining • Tunnel supports • Deformations of pillars • Dams and nuclear power plants • Structural members of buildings and bridges •
Smart Bridge - bridge bearings load control
The distribution can be determined of the load under bridge bearing load-bearing pillars or foundations with multiple sensors BBS 10_DS from IBJ technology. Uneven load entry can detect but also subsequently through still attached directly with sensors built into the bearing plate in the concrete. The applications range from the direct voltage measurement in the component to the measurement and monitoring of dynamic loads in real time. With the sensors is the
Acousto-elastic concrete strain sensors for heavy duty applications
Acousto elastic concrete strain sensors are used to detect the metrological Expansion or compression of steel building components as well as for measurements in reinforced and unreinforced concrete bodies used. The thickness of the susceptor (diameter of the bars) may be selected according to the strength reinforcement. The acousto elastic concrete strain sensors can also be mounted on the outside parts of the structure of steel. With flanges or angle mounting is
Customized sensors for tensile stresses in the concrete
After the patent-pending process of IBJ Technology sensors for strain and compressive stresses can be manufactured in almost all imaginable sizes. The area includes a few inches to several 10 foot length. The diameter of the measuring element can be adjusted to the diameter of the reinforcement in the concrete. The sensor detects the strain or deformation of a metal rod. This metal rod can be arranged in the iron braid

All 5 Releases