Press release
Vehicle and Engine Management System Monitoring with GW-7228
GW-7228 is one of the best protocol conversion solution to read J1939 data. It is a J1939 to Modbus RTU Gateway from ICP DAS USA. It allows data communication between Modbus RTU and J1939 CAN devices. supports PDU1, PDU2, broadcast and destination specific type of J1939 messages. Modbus RTU master can request data from J1939 slave that able to monitor the status of engines. This application are widely used in diesel power-train application, In-vehicle networks for trucks and buses, truck-trailer connections, fleet management systems, on board diagnostics, vehicle automation, and other EMS systems. GW-7228 utility software is provided to configure the parameters and easy to use.
GW-7228 utility software has a simple interface that can configure the module to read specified information. Modbus and J1939 communication parameters can be set on the top helf of the interface. The bottom half section is the J1939 device input/output table. Entered J1939 register will automatically convert to Modbus address. PC, PLC, or other devices can access the data through Modbus RTU(RS-232 port) from GW-7228.
If you have other J1939 requirements or have some questions, we can certainly help you to choose the best solution. Please call our technical support team at (310) 517-9888 X102
Established in 2001, ICP DAS USA is a manufacturer of cutting edge industrial automation and control hardware and software. It offers a broad range of flexible and cost-effective total solutions for various industries, including energy and power, factory and machine, agriculture, aerospace, oil and gas, etc. Its products range from M2M and “Internet of Things” (IoT) controllers and protocol converters to remote data acquisition I/O modules that support a variety of communication protocols including Modbus RTU, Modbus TCP, CAN bus, Profibus, Profinet, Ethernet/IP, HART, EtherCAT, DeviceNet, BACnet, and Wi-Fi.
ICP DAS USA, Inc.
24309 Narbonne Ave. Suite 200
Lomita, CA 90717
sales@icpdas-usa.com
310-517-9888
This release was published on openPR.
Permanent link to this press release:
Copy
Please set a link in the press area of your homepage to this press release on openPR. openPR disclaims liability for any content contained in this release.
You can edit or delete your press release Vehicle and Engine Management System Monitoring with GW-7228 here
News-ID: 391221 • Views: …
More Releases from ICP DAS USA
New DL-100S Series Remote Temperature & Humidity Data Logger with LCD Screen & I …
LOMITA, CA— ICP DAS USA announces a new addition to their growing family of environmental sensors and data loggers, the DL-100S Series.
DL-100S models come with a combination of temperature, humidity, and dew point sensors. The LCD screen gives an instantaneous reading at one glance and onboard storage keeps a record of up to 600,000 sensor readings with accompanying date and time stamps.
An Ethernet connection offers the popular industrial protocol Modbus…
PET-7H16M: High Speed Ethernet Data Acquisition
ICP DAS USA's new PET-7H16M is a high speed data acquisition module with a built-in Ethernet communication port for network data transfer. It includes 8 high speed analog input channels with a FIFO of 2048 samples and a maximum sampling rate of up to 200 kS/s,
with 16-bit analog to digital (A/D) converters simultaneously sampling on each channel. In addition to the Analog input channels, each module provides 4 digital input…
Distributed Data Acquisition And Control System with GW-7472
Distributed data acquisition and control system is widely used in all industrial fields. It is used for implement complex and costly applications. In a single control system, it involves many sub-systems, communication devices, data acquisition modules, and other I/O devices. They usually communicate over different protocols. Gateway or protocol converter would be the key “translate” element between two protocols. Compare to traditional centralized SCADA system, distributed data acquisition and…
Teletrac Navman Partners with ICP DAS USA
ICP DAS USA partners with Teletrac Navman to integrate ICP DAS data acquisition products in Teletrac Navman’s fleet management technologies.
Teletrac Navman specializes in vehicle and equipment tracking using their proprietary software which collects data including GPS position and engine parameters communicated via J1939 protocol. Fleet managers are constantly finding new ways to build a stronger, more efficient fleet. By Teletrac Navman teaming with ICP DAS USA, they were able…
More Releases for J1939
Diagnostic Extension for IXXAT's SAE J1939 Protocol Software
Along with the extension packages for NMEA2000 and ISO15765-2, IXXAT now offers the Diagnostic Extension package according to J1939-73 to extend the functionality of the SAE J1939 protocol software.
During the development of J1939 devices, the implementation of diagnostic services becomes more and more important. Diagnostic messages provide the utility needed when the vehicle is being repaired. They are also used during vehicle operation by the networked ECUs to allow them…
SAE J1939 Designer from IXXAT for cross-product configuration and design
With SAE J1939 Designer, IXXAT offers a cost-effective Windows-based tool for cross-product configuration and design. SAE J1939 Designer comes with a catalog, containing all user-specific parameters (SPNs) and messages (PGNs) defined within the J1939 standard. Thus, the corresponding values can be easily selected and assigned to the device during the definition process. In addition, the creation and maintenance of SPNs and PGNs is possible.
Using the integrated code generators, users can…
NMEA 2000 support for J1939 protocol software from IXXAT
Especially for the development of devices and systems for the maritime sector, IXXAT now offers an extension for its proven J1939 protocol software according to the NMEA 2000 standard. The extension enables the quick and cost-effective development of NMEA 2000 Level A&B Class 1 devices.
The NMEA 2000 Protocol of the National Marine Electronics Association defines messages and mechanisms for applications in the maritime sector.
Besides the "Fast Packet" protocol for rapid…
New Version of the SAE J1939 Protocol Software
IXXAT now offers its SAE J1939 protocol software in an extended and revised version 2.02.
Besides an adaptation of the user interface, which now allows an easy extension of the software functionality via optional modules, e.g. for NMEA 2000 and ISO 15 765, the support of J1939 devices with dynamically adjustable addresses has been improved.
The protocol software is completely written in ANSI-C. Required drivers, to adapt the software to the CAN…
esd electronics, Inc announces the release of its newest software product, the e …
esd electronics, Inc SAE J1939 is a Controller Area Network (CAN) [ISO11898] based protocol developed to provide a standard architecture through which multiple Electronic Control Units (ECUs) on a vehicle can communicate. Based on the extended frame format (29-bit identifier) of the CAN 2.0B specification, it uses a fixed baud rate of 250 Kbit/s.
The esd J1939 Stack design allows quick development of applications supporting the SAE J1939 protocol. Written in…
SAE J1939 API for Microsoft Windows XP/Vista
With the new SAE J1939 API IXXAT offers the J1939 protocol software with a comfortable programming interface as a DLL for Windows XP/Vista and allows herewith the easy implementation of SAE J1939 applications on the PC. It is based on the VCI CAN driver and thereby supports all CAN interfaces form IXXAT.
The 1939 API is currently available for the programming languages C/C++ and Phyton. Support of the .NET framework…
