openPR Logo
Press release

PET-7H16M: High Speed Ethernet Data Acquisition

06-19-2019 08:29 PM CET | Industry, Real Estate & Construction

Press release from: ICP DAS USA

PET-7H16M High Speed Ethernet Data Acquisition Module

PET-7H16M High Speed Ethernet Data Acquisition Module

ICP DAS USA's new PET-7H16M is a high speed data acquisition module with a built-in Ethernet communication port for network data transfer. It includes 8 high speed analog input channels with a FIFO of 2048 samples and a maximum sampling rate of up to 200 kS/s,

with 16-bit analog to digital (A/D) converters simultaneously sampling on each channel. In addition to the Analog input channels, each module provides 4 digital input and 4 digital output channels.

The module provides a programmable input range on all analog Input channels, and the Digital Output can be set to output with short-circuit and
overload protection. The PET-7H16M series also provides 4 kV ESD protection as well as 2500 VDC intra-module isolation.

PET-7H16M supports three different trigger modes for A/D conversion: a software trigger, an external clock trigger, and an external digital signal event trigger (Post-trigger/Pre-trigger). The software trigger can acquire a sample whenever needed, and the continuous A/D acquisition, or the acquisition of N data samples, begins after the command is triggered. In external clock trigger mode, the speed of the A/D acquisition and the amount of data acquired are controlled by external electrical signals. In digital signal event trigger mode, the A/D acquisition parameters are configured by user commands and the A/D acquisition of the N data samples is triggered by an external electrical signal.

Ethernet offers distinct advantages over other data transmission mediums. Ethernet is a reliable, easy-to-install platform with a long transmission distance and fast transmission speed. Not only is Ethernet ubiquitous in enterprise IT, but it is also becoming a mainstream specification for industrial communication.

Most high-speed synchronous data capture systems use a capture card on a computer host to collect data. As projects expand, and the required number of channels increases, especially if data acquisition devices are distributed across multiple sites, the number of computer hosts increases— making the data network more complex than it needs to be.

PET-7H16M is here to simplify that system and replace the computer and capture card. The data collected from different sites is all fed into in a central location, reducing labor time, costs, and extraneous wiring, while providing real-time systems monitoring.

The PET-7H16M can be used for continuous data acquisition, high-speed interval acquisition, and simultaneous acquisition from multiple channels. With a maximum acquisition speed of 200 kHz for each AI channel. It is suitable for high-speed data acquisition of various mechanical, electronic and physical signals in industrial production, automatic control, electrochemistry, medicine, and more.

ICP DAS USA
24309 Narbonne Ave. Suite 200
Lomita, CA 90717
Press Contact: Colin McLeod
cmcleod@icpdas-usa.com
310-517-9888x113
http://www.icpdas-usa.com

Established in 2001, ICP DAS USA is a manufacturer of cutting edge industrial automation and control hardware and software. It offers a broad range of flexible and cost-effective total solutions for various industries, including energy and power, factory and machine, agriculture, aerospace, oil and gas, etc. Its products range from M2M and "Internet of Things" (IoT) controllers and protocol converters to remote data acquisition I/O modules that support a variety of communication protocols including Modbus RTU, Modbus TCP, CAN bus, Profibus, Profinet, Ethernet/IP, HART, EtherCAT, DeviceNet, BACnet, and Wi-Fi.

This release was published on openPR.

Permanent link to this press release:

Copy
Please set a link in the press area of your homepage to this press release on openPR. openPR disclaims liability for any content contained in this release.

You can edit or delete your press release PET-7H16M: High Speed Ethernet Data Acquisition here

News-ID: 1781545 • Views: 1097

More Releases from ICP DAS USA

New DL-100S Series Remote Temperature & Humidity Data Logger with LCD Screen & I …
LOMITA, CA— ICP DAS USA announces a new addition to their growing family of environmental sensors and data loggers, the DL-100S Series. DL-100S models come with a combination of temperature, humidity, and dew point sensors. The LCD screen gives an instantaneous reading at one glance and onboard storage keeps a record of up to 600,000 sensor readings with accompanying date and time stamps. An Ethernet connection offers the popular industrial protocol Modbus
Distributed Data Acquisition And Control System with GW-7472
Distributed data acquisition and control system is widely used in all industrial fields. It is used for implement complex and costly applications. In a single control system, it involves many sub-systems, communication devices, data acquisition modules, and other I/O devices. They usually communicate over different protocols. Gateway or protocol converter would be the key “translate” element between two protocols. Compare to traditional centralized SCADA system, distributed data acquisition and
Vehicle and Engine Management System Monitoring with GW-7228
Engine management system is a build-in system to control and monitor the status of engine, such as engine speed, oil temperature, coolant temperature, oil pressure and other engine parameters. Engine manufacturers always integrate EMS system into engines for diagnostics purposes. EMS is communicated over CAN protocol with SAE J1939 bus. In order to read the engine parameters on computer, users must use protocol converter/ gateway to convert CAN bus to
Teletrac Navman Partners with ICP DAS USA
ICP DAS USA partners with Teletrac Navman to integrate ICP DAS data acquisition products in Teletrac Navman’s fleet management technologies. Teletrac Navman specializes in vehicle and equipment tracking using their proprietary software which collects data including GPS position and engine parameters communicated via J1939 protocol. Fleet managers are constantly finding new ways to build a stronger, more efficient fleet. By Teletrac Navman teaming with ICP DAS USA, they were able

All 5 Releases


More Releases for Ethernet

Humidity Transmitters with Ethernet Interface
Beside the RS485 interface with Modbus RTU protocol, the EE310 humidity and temperature transmitter and the EE360 moisture in oil transmitter from E+E Elektronik now feature an Ethernet interface with Modbus TCP protocol. The EE310 and EE360 represent the latest generation of industrial transmitters from the Austrian sensor specialist E+E Elektronik. A multi-functional 3.5" TFT colour display provides a comprehensive overview of the measurement task and allows the user to
IOP Tester for Ethernet ECUs
RUETZ SYSTEM SOLUTIONS Tests ECUs for Interoperability RUETZ SYSTEM SOLUTIONS – experts for automotive data communications - provides an interoperability test platform for Automotive Ethernet. This IOP tester operates within the framework of compliance tests for Automotive Ethernet. The test platform constitutes a component of the test set-up for Open Alliance Layer 1 interoperability tests for ECUs. The IOP tester allows the verification of ECUs for interoperability with other ECUs
Perle Launches Industrial Ethernet Switches
Perle Systems, a global manufacturer of advanced Ethernet over Fiber and secure device networking solutions, announces its entry into the Industrial Ethernet Switch marketplace. Industrial-grade Ethernet Switches are specially designed to stand up to the extreme temperatures, vibrations, and shocks found in industrial automation, government, military, marine, rail, oil and gas, mining and outdoor applications. By launching over 200 models, Perle now clams the title of having the broadest range
Perle launches Ethernet Copper Extenders
NASHVILLE, TN—November 29th, 2012—Perle Systems, a global provider of advanced Ethernet over fiber and secure device networking solutions, today introduces Ethernet Copper Extenders. Perle Ethernet Extenders are designed for environments where network services are needed beyond the Ethernet limit of 328 feet (100 meters). With network demands often outpacing the original design, Network Administrators are frequently faced with their infrastructure operating at the brink of its capabilities. Copper-based Ethernet connections are
Perle launches 10 Gigabit Ethernet Media Converters
NASHVILLE, TN—September 19th, 2012— Perle Systems, a global provider of advanced Ethernet over Fiber and secure device networking solutions, today introduces 10 Gigabit Ethernet Media Converters. 10GbE Media Converters solve the problem of creating a 10 Gigabit Ethernet link that can be extended from 26 meters up to 160km. The demand for 10GbE is being driven by companies who want their data centers equipped to take advantage of the better performance
New Industrial Ethernet-Connectors from ESCHA
Halver, 26 March 2012 – The Halver/Germany based Connectivity- and Housing manufacturer ESCHA has extended its connectivity line for Industrial-Ethernet-Applications by several products that guarantee a fast and safe data transmission up to 10 Gbit/s. The new M12x1 round connectors with X-Coding as well as the new RJ45-Connectors are respectively available as field wireable- or overmolded variants. Moreover, the connectivity specialist is also introducing a device connection and